保时捷 911 的 TDC 指示器  ❭  SR02

插孔

#北环赛道#

适合：
自 1985 年 8 月起的保时捷 944
保时捷 964
保时捷 968
保时捷 993
保时捷 996 Carrera 2/4 / 996 Turbo
保时捷 997 Carrera 2/4 / 997 Turbo
保时捷 986 Boxster
保时捷 987 Boxster
保时捷 987C Cayman


如果您想在通常的千斤顶位置举升车辆，就不能绕过适配器。只有这样，车辆才能安全稳定地升起，不会有滑落的风险，并且车身底部保护/油漆也受到保护。由于原装支架中的销钉几何形状，该适配器可以旋转，并牢固地固定在车辆上。

优点：
• 采用 7000 铝合金，强度高
• 防止刮伤底盘保护装置/油漆
• 可使用通用千斤顶进行安全顶升
• 锥形轴颈底座具有锁定功能
• 几何形状适合于所提及的保时捷车型。

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

1154

您正在查看的产品与这些编号存在交叉引用关系

Cam timing indicator fixture (dual) for Porsche 911 / 964 / 993



STOMSKI RACING finally takes the guess work out of timing the 911 engines. No longer do you need to hassle with convoluted setups, indicator contacts slipping off of the valve retainer, or measurements that will not repeat. This fixture indexes off of two cam carrier studs and literally takes only 10 seconds to setup. Once in place, the SR098 consistently and repeatedly holds the dial indicator contact in the same place on the valve retainer- EVERY time.

Includes adapters and extensions for both metric and AGD (inch) indicators.
Anodized aluminum for years of service.

For all 911s including the 993.

Please note: Gauges sold separately.

Stomski Racing SR124 Engine case splitter for Porsche 911



No more hammering, chiseling, swearing, heating, prying or praying to get an 911 engine case apart. STOMSKI RACING'S SR124 ELEGANTLY and GENTLY separates the engine case halves and not only shortens the process of engine tear-down, but it also protects what doubtlessly is an expensive asset- the engine case itself. The rare #s matching early 911S sand-cast aluminum case, or the impossible to find 911 GT3 RSR case, or the early magnesium case that seems so fragile, all can NOW be protected from the threat of the block of wood and lead hammer, or the torch, or the pry-bar and chisel.
SR124 includes a CNC precision machined aluminum platform that you bolt to four head studs (ideally over #2 or #5) using the included thumbscrews. An over-sized drive-screw (stainless steel) is then threaded through the platform to mate with a high-load bearing in our specially designed rod cap that presses against the wrist pin of #2 or #5 connecting rod that is at bottom-dead-center. As you slowly use a wrench or ratchet to tighten the drive-screw, the torque of the SR124 splitter is evenly distributed through the entire crankshaft, pressing against ALL 8 main bearings. Once the slack is taken up, only GENTLE effort on the drive screw is required to split even the most belligerent of cases.
The SR124 platform is designed to work on all Mezger 911s (2.0 through 997) and includes Delrin inserts/sleeves that protect the head studs from scratches or dings.