Brake Master Cylinder

Brake fluid DOT 4 20Ltr Textar

Brake fluid is one of the most important fluids in a car as without it, stopping the vehicle safely would be impossible. The Brake fluid transmits the force exerted by the driver on the brake pedal onto the wheel brake. 
To ensure perfect operation of the brakes, the brake fluid must be changed regularly during inspection or maintenance and tested with the correct brake fluid tester.

Brake fluid should be changed every two years. 

The higher the DOT class, the higher the boiling temperature and wet boiling point. Higher DOT classes tend to allow longer maintenance intervals. The DOT standards are based on the American FMVSS-116 standard of the Department of Transportation (DOT).

Boiling Point and Viscosity

Dry Boiling Point - describes the property of the sealed new brake fluid. In this state, the brake fluid is almost anhydrous (substance containing no water). The dry boiling point is usually between 240 and 280°C.

Wet Boiling Point - determines the property of the brake fluid at the end of its life cycle, at a water content of 3.5% the fluid should be replaced. This defined wet boiling point must not be undercut.

Viscosity - describes the flow rate of the brake fluid. The lower the viscosity, the faster the brake fluid flows through the brake system, and the faster the brake signals are transmitted. 

Important Notes
• Brake fluid is poisonous and a hazardous waste.
• Be careful when changing. The fluid weakens paints and plastics.
• It must not come into contact with eyes or skin. Always rinse spilled liquid with water.
• Do not pour the liquid into drinking water or mix with used oil.
• The colour of the brake fluid reveals nothing about its quality.
• Brake fluid should be stored in its original packaging and in a dry, cool and well-ventilated place.

Find out about Textar product verification here

Brake discs, calipers, pads and brake master cylinders are the four cardinal points of each brake system; however, they are likely to be useless without the core of the entire system, the brake fluid. This component is so neglected as to be generally controlled in a summary fashion, with topping instead of a more appropriate replacement, at the change frequency recommended by the manufacturer.

DOT 4
Having an extremely high boiling point and lower viscosity than required, it meets and greatly exceeds regulatory standards. Also suitable for vehicles with ABS.

Vapour Lock formation
This sort of habit leaves room for the Vapour Lock, the formation of vapour bubbles due to boiling of the brake fluid that replace the normal fluid and are compressed, thereby sending the brake pedal to its fill stoke (spongy pedal). The origin is incident in the porosity of the tubes that make up the braking circuit, which in time draw moisture into the fluid, drastically reducing the boiling point. The result is a reduced braking efficiency.

Brembo Premium Brake Fluid
Brembo Premium brake fluids have a higher boiling point that exceeds the standard, thus offering superior resistance to the Vapour Lock and ensuring braking efficiency even at low temperatures. With high anti-corrosion properties and resistance to oxidation, Brembo brake fluid also allows for long-term unaltered chemical/physical characteristics of the fluid in operating circuit; therefore, preserving its integrity.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

L040

The product you are viewing cross references to these numbers

Brake fluid DOT 4 LV (Low Viscosity) Textar.

Textar DOT 4 LV (Low Viscosity) is especially recommended for use in hydraulic brake and clutch systems of vehicles fitted with ESP, ABS and ASR with a high boiling point and outstanding performance at very low temperatures.

DOT 4 LV (Low Viscosity)
Dry Boiling Point ≥ 260° C 
Wet Boiling Point ≥ 165° C 
Viscosity at -40C < 750 mm2 /s

Brake fluid is one of the most important fluids in a car as without it, stopping the vehicle safely would be impossible. The Brake fluid transmits the force exerted by the driver on the brake pedal onto the wheel brake. 
To ensure perfect operation of the brakes, the brake fluid must be changed regularly during inspection or maintenance and tested with the correct brake fluid tester.

Brake fluid should be changed every two years. 

The higher the DOT class, the higher the boiling temperature and wet boiling point. Higher DOT classes tend to allow longer maintenance intervals. The DOT standards are based on the American FMVSS-116 standard of the Department of Transportation (DOT).

Boiling Point and Viscosity

Dry Boiling Point - describes the property of the sealed new brake fluid. In this state, the brake fluid is almost anhydrous (substance containing no water). The dry boiling point is usually between 240 and 280°C.

Wet Boiling Point - determines the property of the brake fluid at the end of its life cycle, at a water content of 3.5% the fluid should be replaced. This defined wet boiling point must not be undercut. <

Viscosity - describes the flow rate of the brake fluid. The lower the viscosity, the faster the brake fluid flows through the brake system, and the faster the brake signals are transmitted. 

Important Notes

• Brake fluid is poisonous and a hazardous waste.
• Be careful when changing. The fluid weakens paints and plastics.
• It must not come into contact with eyes or skin. Always rinse spilled liquid with water.
• Do not pour the liquid into drinking water or mix with used oil.
• The colour of the brake fluid reveals nothing about its quality.
• Brake fluid should be stored in its original packaging and in a dry, cool and well-ventilated place.

Find out about Textar product verification here

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

95006

The product you are viewing cross references to these numbers

Brake fluid DOT 4 



Brake fluid is one of the most important fluids in a car as without it, stopping the vehicle safely would be impossible. The Brake fluid transmits the force exerted by the driver on the brake pedal onto the wheel brake. 

To ensure perfect operation of the brakes, the brake fluid must be changed regularly during inspection or maintenance and tested with the correct brake fluid tester.

Brake fluid should be changed every two years. 

The higher the DOT class, the higher the boiling temperature and wet boiling point. Higher DOT classes tend to allow longer maintenance intervals. The DOT standards are based on the American FMVSS-116 standard of the Department of Transportation (DOT).

Boiling Point and Viscosity

Dry Boiling Point - describes the property of the sealed new brake fluid. In this state, the brake fluid is almost anhydrous (substance containing no water). The dry boiling point is usually between 240 and 280°C.

Wet Boiling Point - determines the property of the brake fluid at the end of its life cycle, at a water content of 3.5% the fluid should be replaced. This defined wet boiling point must not be undercut. 

Viscosity - describes the flow rate of the brake fluid. The lower the viscosity, the faster the brake fluid flows through the brake system, and the faster the brake signals are transmitted. 

Important Notes
• Brake fluid is poisonous and a hazardous waste.
• Be careful when changing. The fluid weakens paints and plastics.
• It must not come into contact with eyes or skin. Always rinse spilled liquid with water.
• Do not pour the liquid into drinking water or mix with used oil.
• The colour of the brake fluid reveals nothing about its quality.
• Brake fluid should be stored in its original packaging and in a dry, cool and well-ventilated place.

Find out about Textar product verification here

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

95002

The product you are viewing cross references to these numbers

Molub-Alloy Paste White T – High Performance Assembly & Anti-Fretting Paste

Molub-Alloy Paste White T is a premium high-performance assembly paste designed to provide exceptional protection against fretting corrosion, stick-slip, wear, and seizure in demanding automotive, industrial, and workshop applications.

This white assembly paste applies cleanly and appears almost colourless when spread as a thin layer, making it ideal for precision assembly work where cleanliness and protection are equally important.

Formulated for universal assembly and thin-film lubrication applications, Molub-Alloy Paste White T helps simplify component assembly and future disassembly while protecting contact surfaces against corrosion, vibration-related wear, and moisture ingress.

Its advanced formulation provides excellent resistance to both hot and cold water while delivering long-lasting corrosion protection under harsh operating conditions.

Particularly effective in applications exposed to vibration and frictional movement, the paste helps prevent fretting corrosion and reduces stick-slip behaviour, making it ideal for hydraulic cylinders, open lubrication points, threaded assemblies, sliding surfaces, and mechanical components subject to oscillating movement.

The product also helps eliminate squeaking noises and improves smooth operation in moving assemblies exposed to high loads and thermal stress.

Suitable for temperatures ranging from -30°C to +250°C, Molub-Alloy Paste White T delivers reliable lubrication and anti-corrosion performance across a wide range of workshop, automotive, and engineering environments.

Key Features

• High-performance white assembly paste
• Prevents fretting corrosion and surface wear
• Clean application with almost colourless thin-film appearance
• Helps simplify assembly and future disassembly
• Excellent anti-seize and separating properties
• Resistant to hot and cold water
• Reduces stick-slip and frictional vibration
• Helps eliminate squeaking noises
• Provides long-lasting corrosion protection
• Suitable for hydraulic cylinders and moving assemblies
• Wide operating temperature range from -30°C to +250°C
• Suitable for automotive, engineering, and industrial applications

Applications

Molub-Alloy Paste White T is ideal for:

• Assembly lubrication
• Anti-fretting protection
• Threaded fasteners and fittings
• Hydraulic cylinders
• Sliding and contact surfaces
• Open lubrication points
• Components exposed to vibration
• Mechanical assemblies requiring anti-seize protection
• Automotive workshop applications
• Industrial machinery and engineering assemblies

Why Use Molub-Alloy Paste White T?

Mechanical components exposed to vibration, friction, heat, and moisture can suffer from fretting corrosion, seizure, stick-slip, and accelerated wear.

Molub-Alloy Paste White T helps protect components by:
• Reducing friction between contact surfaces
• Preventing corrosion and seizure
• Improving assembly and removal
• Minimising vibration-induced wear
• Protecting against moisture and contamination

This makes it ideal for long-term component protection and reliable assembly work.

Temperature Performance

Designed for demanding operating conditions, Molub-Alloy Paste White T remains effective across a wide temperature range:

• Operating temperature: -30°C to +250°C
• Suitable for hot and cold operating environments
• Maintains lubrication and protection under thermal load

Clean & Professional Assembly Solution

Unlike darker anti-seize compounds, this white assembly paste offers a cleaner, more professional appearance during application and servicing.

Benefits include:
• Cleaner working environment
• Reduced visible residue
• Easier inspection during assembly
• Professional workshop finish

Halo GT Advanced DOT 4 Racing Brake Fluid
600ml aluminium bottle

Halo GT is the latest formulation with a DOT 4 base suitable for the demands of motorsport (such as low compressibility and low viscosity). It has a dry boiling point of 336 degrees Celsius which is higher than the Brembo HT64. Whilst withstanding the demands of motorsport, Halo GT is suitable for track day use.

Brake Later. Release Faster. Accelerate earlier. Every Lap.

Halo GT is the ultimate DOT 4 racing brake fluid, fully compliant and optimized for the latest racing ABS systems. Engineered for ultra-fast response, thermal stability, and consistent pedal feel under the most demanding race conditions.

FEATURES

01 | Derived from P1 Proven under extreme conditions. Built on Halo P1 chemistry, developed for the highest demands of motorsport.

02 | Designed for GT racing The ultimate in DOT 4 racing brake fluid, fully compliant and optimized for use with the latest racing ABS systems.

03 | Ultra low viscosity Faster system response for immediate feedback and precise control.

04 | Fade Resistant Technology™ Performance that lasts. Maintains consistent pedal feel under repeated heat cycles with minimal fade as temperatures rise.

05 | Corner focused Control where it matters most. Optimised for braking zones, release precision, and clean transition back to throttle.


Performance benefits

Sharper response. Better control. Faster exits from start to finish.
•  Faster hydraulic response under load
•  Greater stability through repeated braking cycles
•  Quicker piston release for reduced drag
•  More precise brake modulation
•  Reduced thermal stress in extreme conditions
•  Earlier throttle application on corner exit

Speed of Response.
Speed on Track. Modern Braking Systems demand instant response. Halo GT’s ultra-low viscosity allows the brake system to respond faster, improving communication between driver and car.
Faster pressure build-up. Cleaner release. Greater control at the limit.
Brake later. Release faster. Accelerate earlier.

Most races are won in the corner.
Anyone can be fast on the straight. But cornering takes skill. Performance is defined under braking, through release, and on exit. Halo GT is engineered for these moments. Giving drivers the confidence to brake faster, carry speed through the corner, and accelerate earlier. And continue to do that consistently, lap after lap.

For GT drivers who understand Performance.
Not for Everyone. Built for those who demand more.
Also suitable for Semi-Pro, Club Racing and Trackday performance drivers.

Technical Specification.

•  336°C dry boiling point
•  Ultra-low viscosity of 1350 cSt

Designed to maintain consistent performance under heat and repeated load, with full data available for detailed evaluation.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

GTEUK198L2

The product you are viewing cross references to these numbers